Do you ever have a powered window not work all of the sudden? It may go down but it refuses to go back up? If you press on the button and still hear an audible whirring sound but no movement of the window, your motor might still be intact but the window regulator might be bad.
In my case both of my rear window regulators in my E90 went bad within minutes of each other (I suspect due to a recent trip to the carwash.) The windows could still be rolled down, but once they were down they won’t go back up. At the instant the window didn’t roll back up, my car threw an “anti-trap” error. After reading the forums about how much it would cost to get the dealer to fix this issue, I decided to look into fixing it myself.
WARNING: If you’re not mechanically inclined, leave this work to a professional because you may risk breaking glass/puncturing upholstery/severing wires/hurt yourself. This is a straightforward process but consider yourself warned. I suspect that this process is similar for other cars but the steps below are for replacing the rear driver’s side window regulator on a BMW E90 platform.
To replace the window regulators you need a few simple tools. For the E90 you would need the following:
– T20 Torx Driver
– 10mm Socket Wrench
– Plastic prying tool (Screwdriver is ok if you’re careful)
First you’d have to remove the trim pieces that usually covers the major fasteners. This is where having a plastic prying tool comes in handy, once you get some leverage apply even pressure throughout the trim piece and it should pop off.
There are three torx screws that are securing this door panel, the third is hiding behind the handle trim seen below. Once again, use the pry tool or your fingernails to get the trim piece off
Once all three torx screws are gone the door is now held on by plastic ribbed rivets and clips. Before you pop off the door panel it’s best to first disconnect the window button switch from the wires behind the panel. To do this you’d need to use the pry tool again and you have to be careful not to scratch or tear the upholstery as you go about doing this.
You can now pull off the door panel from the door by slowly prying the two apart around the perimeter. There are several ribbed rivets and clips adjoining the door panel so this step will take some effort. Please note that there are two things semi attached to the door panel: the door lock post and wires for the speaker (take note where the speaker wire plugs into)
The sound insulation is foam padding secured to the panel via some gooey acoustical sealant. Separating this insulation will be the weirdest step in this whole process because it feels irreversible and you may feel like it may ruin your car, though if you are careful you won’t end up ripping the insulation and you may be able to reuse the sealant. Also note that if you get this sealant under your fingernails it will be extremely difficult to clean.
At this point you will also need to remove the motor from the window regulator. There should be three screws and you can loosen these with your torx driver.
Note that at this point if you don’t have the replacement window regulator on hand to finish the job you can at least have your window closed and the car’s interior protected from rain.
To ease the installation of the new unit, you need to first mount the motor to the regulator reusing the three torx screws.
Once the motor is secured you can mount the regulator to the door by aligning the three screws on the regulator to the holes in the door frame. Place the three 10mm nuts and loosely tighten them to prevent the regulator from shifting too much as you replace the glass on the green plastic component.
To mount the glass on the glass holder firmly press down on top of the glass and firmly press up on the holder so that the two components click together. The latch of the plastic holder should sit in the hole in the bottom of the glass.
At this point the car had to reprogram the window because it no longer knows when it has completely closed or when it is completely open. Before reprogramming the window would only go up or down in small increments. Reprogramming the window in the E90 BMW is somewhat of a voodoo practice. Some people in the forums have stated that once the window is all the way down, to hold the window switch down for exactly 17 (or 20) seconds and to immediately pull up on the switch. Also, you have to do this on the switch where the window is faulty.
I did exactly this. I sat in the rear driver side seat (the side I have been working on) and held down the switch for 17 seconds and immediately pulled up. Nothing happened. I did it a couple more times to no avail, the window kept on going up or down in small increments. Frustrated, I went to operate the switches from the driver door. All of the sudden the up and down is now back to normal for the repaired window. I went to the rear driver side door again to operate the switches and it functioned normally. Like I said, voodoo.
Now that the window works, the rest of the process is to put the door sound insulation back on. Before mounting the door panel back on ensure that all of the switches are plugged back in and that the door lock mechanism is mounted properly.
You can wrap up by securing the three torx screws back on and placing the trim pieces on the panel.
Once you’re done, give the window and the rest of your car a good wipe down because you’ve probably smudged up the glass pretty well at this point.
Have a DIY of your own, let us know at contact@shiftinglanes.com
Loading…